Skip to content
Email providers

Autocloz + SendPulse

SendPulse connects to Autocloz as an SMTP relay mailbox. Choose Email service → SendPulse on the Mailboxes page, enter the from-address, and paste the SMTP login and password shown in SendPulse under Settings → SMTP. Autocloz sends through smtp-pulse.com on port 2525 and tests the credentials before saving. SendPulse's SMTP service must be activated on your account first, which SendPulse reviews. Replies go to your own inbox; connect that inbox as well to see them in the Unibox.

Autocloz and SendPulse integration
Bring your own accountWorkspace-scoped, no cross-org leakFree-forever CRM core

What you can do with SendPulse

SendPulse plugs into the Email stack — connect via oauth or smtp/imap, scoped to your workspace.

SMTP relay on 2525

The preset points at smtp-pulse.com:2525, SendPulse's published SMTP host and alternative port.

SMTP login from SendPulse

SendPulse generates a separate SMTP login and password once SMTP is activated. Those, not your dashboard login, go into Autocloz.

Probe before save

Autocloz checks the login works before creating the mailbox.

How to connect SendPulse

Connect via OAuth or SMTP/IMAP — you keep control of the account, the spend and the data boundary.

  1. 1

    Activate SMTP in SendPulse

    Request SMTP activation in SendPulse and wait for approval. Until then there is no SMTP login to use.

  2. 2

    Copy the SMTP login and password

    Settings → SMTP in SendPulse shows both.

  3. 3

    Connect in Autocloz

    Mailboxes → Connect mailbox → Email service → SendPulse. Enter the from-address, SMTP login and password.

  4. 4

    Verify the sender

    Make sure the from-address is an approved sender in SendPulse, then send a test.

Checking a SendPulse connection later

If sends start failing weeks after setup, the usual cause is a changed SMTP password or SendPulse pausing SMTP on the account. Autocloz records the SMTP error on each failed send, so the lead timeline tells you which one it is. Update the password on the mailbox, or resolve the account status with SendPulse.

Settings Autocloz uses for SendPulse

From the SendPulse preset:

  • Host: smtp-pulse.com
  • Port: 2525
  • Username: the SMTP login from Settings → SMTP
  • Password: the SMTP password from the same page

Replies from SendPulse sends

SendPulse's relay does not pass replies to Autocloz. Give the mailbox a Reply-To whose inbox is connected to Autocloz over OAuth or IMAP so replies thread with the lead and stop the sequence. If Reply-To is not set, replies go to the from-address, and Autocloz only sees them if that same address is also connected as a reading mailbox.

Limits and pacing

SendPulse plans cap how many emails you can send. Autocloz does not read your SendPulse plan, so set the mailbox's daily and hourly limits and minimum gap to stay inside it. Autocloz applies those limits across every campaign that uses the mailbox, which prevents one busy campaign from using up the day's allowance for all the others.

SendPulse SMTP versus SendPulse campaigns

SendPulse sells both a campaign builder and an SMTP relay. Autocloz uses only the relay. Your contacts, lists and sequences stay in Autocloz; SendPulse sees individual messages. That means SendPulse's campaign reports will not show Autocloz sequences as campaigns, and Autocloz tracks opens, clicks and replies on its side.

Keeping a SendPulse sender in good standing

SendPulse reviews SMTP accounts and watches complaint and bounce rates. Verify addresses before sending, keep follow-up counts reasonable, and honour opt-outs. Autocloz adds an unsubscribe link and suppresses unsubscribed addresses automatically. See reducing bounce rate and bounce rate basics.

What SendPulse does not do in Autocloz

  • No SendPulse campaign, list or template sync.
  • No reply reading through SendPulse.
  • No sending until SendPulse activates SMTP for your account.

Troubleshooting SendPulse

Login fails.
Use the SMTP login from Settings → SMTP, not your SendPulse account email and password.
No SMTP settings visible in SendPulse.
SMTP has not been activated yet. Request it and wait for approval.

Part of the Email stack

SendPulse is one of the providers behind the Email channel. All mailboxes share the same sequencing, unified inbox, and deliverability tooling regardless of provider.

Explore the Email feature

Related integrations

Frequently asked

Is SendPulse free with Autocloz?

Autocloz does not charge for connecting SendPulse. SendPulse bills you for SMTP volume under its own pricing.

Does Autocloz sync SendPulse's unsubscribes?

No. Autocloz keeps its own suppression list from unsubscribes, bounces and DNC entries, and checks it before every send.

Can I send from several domains?

Yes, if each from-address is an approved sender in SendPulse. Connect each address as its own mailbox.

Will my sends show in SendPulse's statistics?

SendPulse counts relayed mail on its side. Autocloz keeps separate per-campaign statistics.

Run SendPulse inside Autocloz

Bring your own account, plug it into the Email channel, and keep a free-forever CRM for 3 users.